CT-100 - Agilent CT-100 Aktivní měrka hrubého vakua
Pro více informací, prosím, kontaktujte prodejce:
- Ing. Vojtěch Kroupa
- +420 736 473 797
- vojtech.kroupa@labtech.eu
Technická specifikace
| Pressure range | Factory setting |
| N2/Air | (1.000 V @≤ 1 x 10–5 Torr): |
| 1 x 10–4 to 100 Torr, sensitive to ATM | |
| (1.33 x 10–4 to 133 mbar, sensitive to ATM) | |
| (1.33 x 10–2 to 1.33 x 10–4 Pa, sensitive to ATM) | |
| Optional User Setting (8.255 V @ATM): | |
| 20 mTorr to ATM | |
| (2.6 x 10–2 to 1000 mbar) | |
| (2.6 to 10–5 Pa) | |
| Response time | 0.2 second |
| Relay response time | <1 msec |
| Setpoint adjustment range | Greater than gauge pressure range |
| Operating temperature | 15 °C to 50 °C, 90% relative humidity non-condensing |
| Storage temperature | –15 °C to 85 °C |
| Mounting orientation | Vacuum port pointing down for best results above 1 Torr (1.33 mbar, 133 Pa) |
| Weight with NPT Fitting | 113 grams (¼ lb) |
| Interface | |
| Two setpoints | Two user defined pressure setpoints for process steps, alarms, high vacuum gauge trigger, or other pressure-induced events |
| Setpoint | Dual, non-isolated, open collector output |
| “Contact” Rating | 0.3 VDC @100 mA (on), 30 VDC Max (off) |
| Adjustment | Trim pot, panel calibration, fixed hysteresis |
| Analog voltage proportional to threshold available at connector (0 VDC – 12 VDC referred to analog output), output impedance 100 kohms | |
| Input voltage/power | 13 to 30 VDC @0.125 AMP, protected against reversals |
| Output signal (analog) | Non-linear, 1 to 9 VDC, nominal |
| Fault | <0.5 VDC or >9 VDC (for N2) |
| Output impedance | 100 ohms |
| Displays | |
| Setpoint indicators | Red LEDs – Verify an operation is underway and the appropriate vacuum has been achieved |
| Vacuum indicator | Green LED – Indicates <100 mTorr vacuum is achieved |
| Materials of construction | |
| Materials exposed to vacuum | Nickel-plated mild steel, glass, nickel alloy (⅛" NPT) 304 SSt, glass, nickel alloy (NW16) |
| Casing | Flame retardant ABS (Acrylonitrile-butadiene-styrene) |
| Sensor element | Platinel |
| Sensor internal volume | 5.4 mL |
| Connections | |
| Electrical | 9-pin D-Sub |
| Hardware | ⅛” NPT or NW16 KF |
| Certification | UL Recognized, cUL Recognized |
| CE | EMC: EU 89/336, EN55011, EN61326 |
| Safety: 73/23/EEC, Low Voltage Directive | |
| EN61010 |
Ke stažení
Dokumenty ke stažení
Máte dotaz?
LABTECH s.r.o © 2014, Pracoviště Telnice, K nádraží 191, Telnice 664 59, Tel: +420 511 192 927, Fax: +420 543 210 115, info@labtech.eu